Search:

Love the deck space upfront. Also love the spread between the outboards, she should be real stable.

Choc-kits with a glass of milk.

School me.

From what I understand the cat hull is not a good idea as the central portion between the hulls is too low and slaps hard on the waves. A mono hull is preferred.

Just looking for...

Was at lunch yesterday and one bloke opined that with the flooding of the Toyota factory in Durban that Fortuner availability is shifting out to 12 month as all stock and WIP on the floor has been...

Winter is a great leveler of batteries.

Agree and disagree. On the one hand you have the design component which is subjective and beauty is in the eye of the beholder. Bad workmanship is not subjective, poor welding is unsightly as are...

Or you ran out of patience required for the level of detail you wanted. The master craftsmen had no fancy machines at hand but they had the time and patience to create incredible things. I have been...

Form surprisingly does not take that much more effort. Make drawings so you don't constantly re-engineer and or botch the design through unsightly additions.

For me they are equal. I was...

Offer withdrawn, donated elsewhere.

How I wish this was true.

On heavier stuff I have used two of the smaller ones in tandem and made balance bars with variable weights to reduce the torque requirement. Balance bars are a great addition, reduces the motor load...

As the battery ages the copper from 6 anodes slowly migrates deposits on the 6 cathodes, eventually there is too little copper on the anode side to allow for any charge to flow. The deposits are...

If I recall correctly there is a loss on power as the gas is less efficient than a fuel. Check that out as well. Our forklifts had the gas conversion and we could not lift what we used to. Maybe...

I had some left field thoughts. What would be the landowners culpability be with regards to erecting a barrier that may result in the death of an errant driver?

Such a barrier, if legal, would...

Peter the steel I believe is for the shafts through the bearings so black steel would not be ideal. The ally would work.

Perhaps refine your search.

I have not seen self tappers referred to as M2. M2 would indicate a standard metric thread of 2mm diameter. Rather google 2mm Self tappers. 9mm is also a non standard...

How do you keep the dust and water out?

I have great sympathy for those downstream as it must be a nightmare, logistically and financially.

I was wondering what would have happened before the dam was built? Would the flooding not have...

I am sure some have ignored the flood line and have built below it.

Vaal Dam

116.55% Full
Inflow : 1354m3/s
Outflow: 1336m3/s

The Dam can go up to 126% full, this is the servitude level. However, then there is no reserve capacity if more rain falls in the...

I suppose what confused me is that the Chinese would include a 3W Pot when this was over the top. It is normally the reverse. Bought a 40A SCR once that failed, on opening the controller the SCR was...

Not sure I understand Fluffy, school me.

So at 220V I am OK?

As I thought that was necessary to get the wattage rating?

The application is as the control pot for a SCR Controller which comes supplied with a 500k 3W Wire Wound pot. The pot is too coarse and...

Hi,

I am looking for the above pot. 5W is physically to big to fit into the tight space. Can find 22k pots but not 47k.

According to my grandson Bacon should be a food group of its own.

High airflow creates "case hardening". Where the outside of the biltong dries at a rate too fast for the inside. You end up with dry outside and raw inside. Does not work for me at least.

Indeed, I had considered perspex or smoked glass. Love the soft glow of valves.

Thanks for the offer though it is appreciated.

Many thanks for the offer.

These would be the the rough finished sizes. Hard to get at the Amp right now is is is packed deep.
The top is 450mm(w) x 340mm(d) one piece.
The sides are 340mm(l) x...

You may be right. All I require however to prevent dust and crud from entering and to protect the components.

653550

Old and grubby but still sounds really nice. When I recap her I will give...

Take the lid off then and you are braaing!

And not a camper of 120kg's like me ;).

I believe that orientation is specific to the cover that is over the terminals. Any other orientation would allow for the ingress of water if present.

Should have googled veneered MDF board, Leroy Merlin has 3mm.

The 70's style Amplifiers had a metal chassis, front and rear but the sides and top were made from very thin laminated wood grain plywood.

I need to make a cover for my 70's valve amp. Where can I...