Search Results - 4x4 Community Forum





Search:

Type: Posts; User: oldnslow; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    3,767

    Re: Steed optimising

    What is the max boost pressure you got?
  2. Replies
    29
    Views
    17,126

    Re: GWM Manuals and documuments

    https://drive.google.com/open?id=12xbRK4F5CT5k_vE4B1X_5J68Zil6norf
  3. Replies
    29
    Views
    17,126

    Re: GWM Manuals and documuments

    does this forum have a place I can upload them to - so we have them for all time?
  4. Replies
    29
    Views
    17,126

    Re: GWM Manuals and documuments

    here is a link to the GWM Diesel engines
    including the 2.5 tci turbo engine
    https://drive.google.com/open?id=12xbRK4F5CT5k_vE4B1X_5J68Zil6norf
  5. Replies
    29
    Views
    17,126

    Re: GWM Manuals and documuments

    hi Folks,
    I'm trying to set the timing on my GWM Hover 2.5 diesel - does anyone know where the timing marks or a engine manual can be found pleeeeaase ... getting desparate!
    same engine as the 2.5...
  6. Re: hesitation on acceleration and speed lagging

    I'm not going mention the dealership's name, however:
    They had the vehicle for a day and told me that they could not find parts for it, and I had to call them to find out what was going on ---...
  7. Re: hesitation on acceleration and speed lagging

    Dropped it off at the dealer this am - lets see what they say
  8. hesitation on acceleration and speedo lagging

    Hi folks,
    I should have known - every time I brag about my vehicle I end up with issues. I told someone last week that my GWM Hover 2010 (2.5 turbo diesel) has never given me any real...
  9. Replies
    1
    Views
    681

    Re: Speedo stopped working

    the speed sensor is toast ..... R250
  10. Replies
    1
    Views
    681

    Speedo stopped working

    Hi Folks,
    GWM Hove Diesel 2.5 l --- speedo reads 0 ... anyone know where the speed sensor is located or has any ideas on how to fix this, please?
  11. Planning trip to Moz - Inhambane / Tofo area

    Hi Folks,

    we are newbies to over landing in Moz - we are planning a trip in early March and were wondering if anyone else was planning a trip to Tofo or Inhambane area in March so that we could...
  12. Replies
    31
    Views
    6,063

    Re: Diesel additive question

    This is dependent on the the motor's set up, if its operating range is much higher than its daily use it will get carbon build up (over a long period) -- sustained relatively high rpm (under load)...
  13. Replies
    31
    Views
    6,063

    Re: Diesel additive question

    For diesel mains and cleaning use a cup full of auto tranny fluid into the fuel filter.
    Diesel needs an anti-fungal if you live in a hot place and donít use much fuel, like if your driving only uses...
  14. Re: Anyone going 4X4 tomorrow near Cape Town?

    thats correct - I'm in Cape Town for a while.
  15. Re: Anyone going 4X4 tomorrow near Cape Town?

    Hi Chris,
    DeWild is west of Pretoria, its a 4x4 and game park - fun spot.
    Yeah, I know its short notice, had my head buried in work, and I'm hopefull.
  16. Anyone going 4X4 tomorrow near Cape Town?

    Hi Folks,

    I'm new to the Cape Town area and was wondering if we could meet up with some folks for a moderate to easy (like De Wilde) 4x4ing and socializing tomorrow, please?

    BTW the avatar is...
  17. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Re: Odbii

    Hi Stoffie,
    I would make the assumption the switch is bad - find out it there is diagnostics you can do on the switch or get another one from GWM or a scrap dealer
  18. Replies
    4
    Views
    1,441

    Re: P0382: Glow Plug/Heater Circuit "B"

    Cool thank you
    I'll go buy some glow plugs from GWM
  19. Replies
    4
    Views
    1,441

    Re: P0382: Glow Plug/Heater Circuit "B"

    HI Pierre,

    The glow plugs are from Midas and the controller is from GWM
  20. Replies
    4
    Views
    1,441

    P0382: Glow Plug/Heater Circuit "B"

    Hi Folks,
    I need some help......I replaced the glow plugs and I replaced the glow plug control switch/relay.
    And then reset the fault -
    A day later the error is back --
    any one got any ideas...
  21. Replies
    22
    Views
    5,021

    Re: Whine after egr delete

    The whine is coming from the the turbo - when you put in the blank plate you tweaked the alignment to the turbo.
    this is not good
  22. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Hi Duncang, LOL, Identifying and replacing the...

    Hi Duncang,

    LOL, Identifying and replacing the bad glow plug was the first step - then when the engine light did not go off I went into the cycles that spawned this thread.

    Else we would go...
  23. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Hi Pierre, After we reset the error message the...

    Hi Pierre,
    After we reset the error message the engine light went out and stayed out all day and then last night as I turned the engine off - it came back on - really odd - this might be the voltage...
  24. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Hi Pierre, I took it entirely out when I...

    Hi Pierre,

    I took it entirely out when I blanked it, sorry no wires, my engine must be an anomaly. I also skimmed the mating search to allow a couple of mm's of room for the blanking plate, when I...
  25. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Spitvurk, if I'm not mistaken the ELM327 is...

    Spitvurk,

    if I'm not mistaken the ELM327 is the "translation" layer between R232 (serial on the ODB side) and the db9 protocol (USB) on the PC side, I'm getting really suspicions of the odb cable...
  26. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Kleinlots, where are you located? I'm more...

    Kleinlots,

    where are you located? I'm more interested in why the light is on not that I have the reset tip?
  27. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Hi Pierre, the solenoid has no wires - its...

    Hi Pierre,

    the solenoid has no wires - its vacuum controlled, this might be a diff between the Steed and Hover.
    Thank you for the reset tip - I'll give that a whirl.
  28. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    It takes Isuzu glow plugs.

    It takes Isuzu glow plugs.
  29. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Hi Pierre, the egr solonoid on this engine to...

    Hi Pierre,
    the egr solonoid on this engine to vacum driven and I have deleted it (blocked it off), Last time this happened it was a glow plug that had shorted out, quick easy fix, but I used...
  30. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Hi Eagle Eye - yes the uart drivers are needed to...

    Hi Eagle Eye - yes the uart drivers are needed to support Future technologies - I included them when I compiled the freediag tool
  31. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    engine - not spanner

    engine - not spanner
  32. Thread: Odbii

    by oldnslow
    Replies
    36
    Views
    3,378

    Odbii

    Hi Folks,

    My Hover 2.5 diesel 2011's check engine light has come on and I'm trying to connect an ODBII reader to it to figure out what the issue is, however I can't seem to connect.

    I'm using a...
  33. Replies
    57
    Views
    8,183

    ouch - hope they picked up the repair bill

    ouch - hope they picked up the repair bill
  34. Replies
    57
    Views
    8,183

    I noticed the when I was fabricating the egr...

    I noticed the when I was fabricating the egr delete plates and had the system open that the egr puts some nasty crap back into the engine (quite solid lumps of carbon etc). I think this motor will...
  35. Replies
    57
    Views
    8,183

    cool thanx - being a dirt biker I have lots of...

    cool thanx - being a dirt biker I have lots of chain lube and I'll check the UV's
Results 1 to 35 of 84
Page 1 of 3 1 2 3