Search:

i went through this process last month[emoji17].according to service book the belt was changed on 180k km,but.........[emoji85]for my peace of mind i asked my indy to open it up and replace the whole...

Hi,get it plugged in asap to get the fault codes.
to me it sounds like you have a stretched timing chain.cam and crank signal out of sync.sometimes if its stretched slightly it wouldn't register a...

i have a set for you,came from my triton,its general grabber at3.the spare has a gaitor.603251603252

According to current and previous owners of the same model tritons on the forum, the best size will be 17mm for the front.

so i spoilt myself with this,now to start with the mods.bought 25mm front spacers,but quickly learned that it will cause problems.602737602738602739

Try LR service in Epping,

Thank you for the feedback,maybe i'm in the same boat.only the four(4)x tyres that was on the vehicle was send off to the supplier.will report back.

Regards.

Took mine back today(5),was fitted in september.dealer phoned his supplier that also gave the 10% story.i only truly realise there was trouble after i did the rotation back to front on the vehicle.i...

My friend had the same problem,it turned out to be the ball joint on the LCA, He had to grind off the ball joint,as this was one with the LCA.the "studs" was replaced with bolts and nuts.the pic is...

Did this two(2) weeks ago[emoji2960]all good so far.590435

@ Mcdonalds N1 city [emoji2960]575357

JJJ,the guy with awealth of knowledge on softies.Im sure he'll be around soon for a few more tips.[emoji16]

N bietjie van als[emoji16][emoji108]

Well done,Now you only have to check your wheel alignment.
Regards.

It looks very nice.[emoji108]

Wow,waars die kwyl knoppie.Is that the original land rover rim on the vehicle?

I have the same issue,Try masterparts bellville,i purchased four(4)x kyb shocks on the 7th.the shocks must still be installed.Acrotek quoted me R9k for four(4) x shocks,including new shock mounts.

I tried the DTE pedalbox.it kept on putting the vehicle into limp mode...tried two different models,no luck........

Please consider that timing belt..
Regards

Hi,just for information,checkout the ravenol website,most vehicle specs and recommended oils on there.
Regards

Thats terrible,my guess would be that fuel sender unit in the tank.strange that no fault code is stored.i hope the matter can be sorted a.s.a.p.
Regards.

Shhhhhh!!![emoji850]

Maybe a good clean of the MAF sensor?
Regards.

Its pointing to the fuel sender unit within the tank.maybe someone will be able to shed more light on the issue.
Hope you get sorted.
Regards.

It might even be a dirty fuel filter.

Yes,the crank position sensor will cut out the engine.
One member on the forum had the engine cut out whilst driving.
I'm sure you will find the thread on the forum related to that issue.im not...

Hi,maybe it might be a faulty crank sensor.
Since you say it sounds like it wants to start.
Im sure somebody will be along shortly to advise.
Regards

Awesome[emoji108] my plesier.keep well

I paid R200 for my tool,im glad you got the pulley,hope you get sorted.
Regards.

Yes its a fairly straight forward swop.the part is.
- Electro part clutch pulley(6002783768324
- PUL 1074 (on the midas system)
Regards
-

It just came to me now[emoji85]
The actual tool is a bit to long to to slide into the alternator pulley whilst insitu,so i disasembled the removal tool,put a more short spline into the shaft.the...

Insitu,with the special removal tool,will post a pic later

Only the pulley on the alternator,

I think most midas will stock that pulley,i bought the removal tool from tengtools.
Diesel Electric advised me to buy said pulley.
Said exercise cost me less than R700[emoji85] The combo of the...

My tensioner was also bouncing whilst vehicle was idling,i replaced the pulley with a part sourced from midas as per pic,the pulley is still holding up,tensioner bounce is gone.anyway i hope you get...